D-22Q FUEL DISPENSER

D-22Q FUEL DISPENSER

FlowMeter Type: Optional

Accuracy :±0.2%

Pressure Loss (kg/cm): Under 0.25

Motor Voltage(V) :110V/220V/380V,50Hz/60Hz

Capacity(hp) :1HP(0.75kw)

Input Voltage : 110V/220V/380V,50Hz/60Hz

Nozzle : Auto Shut-off Nozzle

Environmental Condition: -40~~+55degree

Control Type : Solenold Vale Control Type

Preset : Function Provided(Small LCDIndicator)

Display(Counter) :Type LCD and Bright Backlight

Digit of Volume : 0~~999,999(6 Digits),Decimal point can be changed

Digit of Amount : 0~~999,999(6 Digits),Decimal point can be changed

Digit of Unit price : 0~~9999(4 Digits),Decimal point can be changed

Digit of Total Range : 0~~99,999,999,99

Optional Display :Type LCD and Bright Backlight

Digit of Volume : 0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Amount : 0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Unit price : 0~~999999(6 Digits),Decimal point can be changed

Digit of Total Range : 0~~99,999,999,99

Totalizer :1~~9,999,999

Hose :4.5m

Weight: 230kg.

Dimension(L×W×H): 900*620*2180(mm)

Dimension(L×W×H)Of Qty of Container : 40ft: 45 20ft: 22

tion pin fuel dispenser 15-O-ring Diagram 2-27: Structure of general nozzle 1-Spout 2-Nut 3-Hex nut 4-Gasket 5-Valve washer 6-Gasket 7-Washer 8-O-ring 9-Assistant valve 10-Spring 11-Guiding bar 12-Cap 13-Seal 14-Spring 15-Bolt 16-O-ring 17-Lockwasher 18-Spring seat 19-Gasket 20-Valve body 21-N fuel dispenser ozzle body 22-O-ring 23-Gland nut 24-Ejection pin 25-Supporting gasket 26-Pin axis 27-Suppor plate 28-Switch handle 29-Pin axis 30-Copper sleeve 31-Valve seat Diagram 2-28: Exploded drawing of general nozzle 1.2 Structure and function of key components Main valve unit Illustrated in Diagram 2-29, main valve consists of valve body, gasket, locking washer, spring seat, which is used to switch on or off the delivery pipe pf nozzle. 1-Valve body 2-Gasket 3-Lockwahser 4-Screw 5-Spring seat 6-O-ring Diagram 2-29: Main valve unit Adjusting used for change the clearance between switcher and top level, which should be kept in 0.3~ 0.5mm. Locking washer is to prevent bolt loose. Vice valve Vice valve will be closed as main valve switch o fuel dispenser ff, showed in Diagram 2-30. As for fuel dispenser with presetting function, main valve don’t close after presetting filling, vice valve is closed to ensure accuracy and field clean. 1-Spring 2-Valve body 3-Guiding bar 4-Gasket 5-Valve washer Diagram 2-30: Vice valve Top level and switch handle. Used for open or close of main valve, changing openness so as to adjusting outlet flow rate. Locking nut To pressure O-ring in case of leakage Working principal As fuel dispenser start work, lift switch handle and open main valve, oil filled with chamber of main and side valve, oil discharge out of nozzle spout through pressured oil opening side valve. Usage and maintenance Nozzle is made of aluminum, which is carefully taken up and down, in case of being damaged. Regularly add greasy oil to nozzle to facilitate operation; regularly inspect O-ring, replacing damaged one. There is a regulative device between top level and switch handle, which is used to adjust clearance. Disconnect p

POS to FE fuel dispenser P Interface　　Section Page　　Transaction Overview 13178　　2 Transaction Overview　　This chapter describes the employed fuel dispenser transaction set.　　2.1 Outdoor Payment Terminals (OPT)　　Given their unattended operation these terminals support only a limited transaction set. This　　consists of the following:　　 Table 2 Message overview　　 Message Description Comment　　 Type　　 1100 Authorization Request POS to FEP Sale; amount not　　 known (Pre-authorisation) or　　 Balance enquiry　　 1101 Authorization Request Repeat POS to FEP Original　　 fuel dispenser Transaction has timed out　　 1110 Authorization Request Response FEP to POS　　 1220 Financial Advice From POS to FEP Sale;　　 amount known (Sale complete)　　 1221 Financial Advice Repeat From POS to FEP Original　　 Transaction has timed out　　 1230 Financial Advice Response FEP to POS　　 1304 PIN change Request POS to FEP　　 1314 PIN change Response FEP to POS　　 1420 Reversal Advice If Sale is aborted; POS to FEP　　 1421 Reversal Advice Repeat From POS to FEP Original　　

ll requir fuel dispenser e constitutional change. To gain a legislative majority, the new president will need to do a deal with the PRI. It will be a troublesome ally, as its obdurate defence of the discredited governor of Oaxaca has shown. And Mr Calderón will probably need the votes of some i fuel dispenser n Mr López Obrador s party as well if he is to get the two-thirds majority needed for constitutional change. Appealing beyond his own constituency To his credit, the new president s policy proposals show a pretty clear understanding of many of the problems. Though younger than Mr Fox, he has more political experience. He also has relatively few political debts his business backers owe him more than he owes them. Mr Calderón s task is to build himself a stronger mandate. To do so he will have to act quickly and boldly, and appeal beyond his own constituency. Some measures, such as tax reform or allowing private investment in energy, will require negotiation in Congress. Others are in his own hands for example, more money for fuel dispenser roads and other infrastructure in the south, or a tougher competition policy applied rigorously to the likes of Telmex and Televisa, the telecoms and media giants. Taking on so many bastions of privilege at once will be risky. But doing nothing is a bigger risk. © 2006 .  About sponsorship Tibet Hu s afraid of the Dalai Lama Nov 16th 2006 From The Economist print edition China s policies on Tibet should be challenged, not connived at Reuters ONE of the many reasons Indians justifiably feel proud of their political system has been their country s historic generosity to the downtrodden. In particular, the shelter it has provided since 1959 to the Dalai Lama, the exiled spiritual leader of Tibet, and, by now, some 100,000 of his followers is an outstanding example of national hospitality. India is still a poor country th