F-GB6Q FUEL DISPENSER

F-GB6Q FUEL DISPENSER

FlowMeter Type : Optional

Accuracy :±0.2%

Pressure Loss (kg/cm) :Under 0.25

Motor Voltage(V): 110V/220V/380V,50Hz/60Hz

Capacity(hp): 1HP(0.75kw)

Input Voltage :110V/220V/380V,50Hz/60Hz

Nozzle: Auto Shut-off Nozzle

Environmental Condition : -40~~+55degree

Control Type :Solenold Vale Control Type

Preset : Function Provided(Small LCDIndicator)

Display(Counter) :Type LCD and Bright Backlight

Digit of Volume : 0~~999,999(6 Digits),Decimal point can be changed

Digit of Amount :0~~999,999(6 Digits),Decimal point can be changed

Digit of Unit price: 0~~9999(4 Digits),Decimal point can be changed

Digit of Total Range :0~~99,999,999,99

Optional Display :Type LCD and Bright Backlight

Digit of Volume : 0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Amount :0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Unit price : 0~~999999(6 Digits),Decimal point can be changed

Digit of Total Range : 0~~99,999,999,99

Totalizer: 1~~9,999,999

Hose :4.5m

Weight :350kg

Dimension(L×W×H): 1860*660*2190(mm)

Dimension(L×W×H)Of Qty of Container :40ft: 17

. Examine clearance and replace relevan fuel dispenser t components when necessary. 1.4. Measurement transducer block 1.5. No discharge due to Solenoid valve closed. First check electric wiring, then trouble on component itself (short circuit of winding or block in valve membrane, etc). 1.6. Pipeline and bottom valve failure If continuously exhaust in vapor separator from beginning, disconnect filter cover and take out filter net; pour same kind of oil in it and given see oil level quickly drop, there is leakage occurred in pipeline and bottom valve. 1.7. No discharge caused by nozzle failure Jam in jointer or filter. Unlock strainer or jointer to remove dirt and waste. Nozzle always in auto-shut state, check automatic shut device, mainly inlet vent, spring. 1.8. Bottom valve be stuck in and pipeline is plugged. Exterior reasons for no delivery Oil level is so lower than bottom valve that pump can’t suck oil. Some valve(s) is closed in pipeline between tank and fuel dispensers. Air goes into valve(s). Single phase valve is rusted in bottom valve. Incorrect installation of flange causes leakage between inlet pipe and fuel dispenser. Inappropriate oil is refueled. Oil is easy to gasify; water in oil freeze; wax in oil plug pipe. Pipe design is unsuitable. Two fuel dispensers, for example, are connected in same pipeline without valve, or valve can’t shut completely; pipeline has many crooks or too thin. Slow flow rate as starting 3.1. Strainers, including cone-shaped filter net and nozzle filter net, are jammed. 3.2. Large amount of air flow into from broken parts or pipeline, causing much foam in oil indicator. 3.3. Large noise and vibration during operation Vacuum pressure is inadequate. Leakage occurs in overflow valve or pump gasket. fuel dispenser Inner leakage in fuel dispenser increase as serious abrasion in pump vane or vane is stuck by waste. Vapor separator trouble Small floater of vapor separator is broken or fall down; insufficient pressure in high pressure chamber as exhausting valve can fuel dispenser

ayment ................................ fuel dispenser .................................................................................................48　　6. ADDITIONAL IMPLEMENTATION EXAMPLES........................................................................................................49　　 6.1 PRINTING CARD RECEIPTS................................................................................................................................................ 49　　 6.2 TRACK DATA CODING ......................................................................................................................................................49　　 6.3 SWIPE AHEAD .................................................................................................................................................................49　　 6.4 DEVICEREQUEST FOR MENU ............................................................................................................................................51　　 6.5 DEVICEREQUEST EVENT ...............................................................................................................................................51　　 6.6 SERVICEREQUEST ADMINISTRATION.............................................................................................................................52　　 6.7 SCENARIO OF HAVING THE SALESTRANSACTION DETAILS CHANGING DEPENDING ON THE CARD SWIPED........................ 53　　7. EXAMPLE OF IMPLEMENTATION FOR OUTDOOR PAYMENT TERMINAL ...................................................53　　 7.1 COPT....................................................................................................... fuel dispenser .......................................................................53　　 7.2 CRID PAYMENT PROCESS ................................................................................................................................... fuel dispenser

message through the media by issuing a fuel dispenser one-way press release, but that s as flawed right now as a 15 or 30-second TV ad,�? says Pam Talbot, Edelman s chief in America. The fragmentation of media has seen an explosion in the number of ways people seek news and entertainment, with many turning to websites, cable TV, satellite radio and podcasts. Yet a consequence of the proliferation of media is that original content becomes even more sought after. Hence crisply written or well-produced PR material can more easily get an airing. Media commentators have noted how PR material is now being published by some local newspapers virtually unedited and unchecked. Some branches of journalism have come to depend on a drip- feed of information and products from the PR industry. Journalists focusing on electronics, fashion, travel, beauty and food have a huge appetite for free samples. Gossip about celebrities is also largely mediated by the PR industry. Never shy about accentuating the positive, the PR industry might be expected to be trumpeting its rise. And there is indeed some triumphalism (and spin) around. Al and Laura Ries, a father and daughter team of marketing consultants, have written a book entitled “The Fall of Advertising & the Rise of PR�? “PR has credibility,�?they assert “Advertising does not.�?Their advice is that a marketing campaign should start with publicity and shift to advertising only after the PR objectives have been achieved. Some PR firms see an opportunity to move up their clients hierarchy—becoming not just service providers, but also purveyors of strategic advice to senior management. But even within the industry, there are sceptics. Dorothy Crenshaw, president of Stanton Crenshaw, an independent PR firm based in N fuel dispenser ew York, says that many of her colleagues are suffering from “consultant envy”�? but that PR remains a very inexact science. There are also limits to the miracles it can be expected to achieve. She claims to have turned down a $1m commissi fuel dispenser